BGJFG - U0-082, POLYAMID,MIL-C-22750,PART B
- MSDS: BGJFG
- Manufacturer: CRAWFORD LABORATORIES INC
- Product Name: U0-082, POLYAMID,MIL-C-22750,PART B
- National Stock Number: 8010-01-053-2646
Product Identification
Product ID:U0-082, POLYAMID,MIL-C-22750,PART B
MSDS Date:01/11/1988
FSC:8010
NIIN:01-053-2646
MSDS Number: BGJFG
Responsible Party
CHICAGO, IL 60609
Emergency Phone: 312-433-1307
Info Phone: 312-376-7132
Cage: DO165
Contractor
Telephone: 312-376-7132
Cage: 5V430
Ingredients
ISOPROPYL ALCOHOL (SARA III)
CAS: 67-63-0
RTECS: NT8050000
Fraction By Weight: 50-75%
OSHA PEL 400 PPM/500 STEL
ACGIH TLV: 400 PPM/500STEL;9192
METHYL ETHYL KETONE (2-BUTANONE) (MEK) (SARA III)
CAS: 78-93-3
RTECS: EL6475000
Fraction By Weight: 20-50%
OSHA PEL 200 PPM/300 STEL
ACGIH TLV: 200 PPM/300STEL 9192
EPA Report Quantity: 5000 LBS
DOT Report Quantity: 5000 LBS
Hazards
LD50 LC50 Mixture:N/K
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:(SEE SIGNS & SYMPTOMS OF OVEREXPOSURE)
Explanation of Carcinogenicity:N/A
Effects of Overexposure:OVEREXPOSURE MAY PRODUCE VARIOUS EFFECTS,
INCLUDING:1-ACUTE TOXICITY, RESULTING IN HEADACHE,
DIZZINESS,NAUSEA, & LOSS OF CONSCIOUSNESS. 2-EYE IRRITATION.
3-IRRITATED MUCOUS MEMBRANES. 4-VOMITING DUE T O INGESTION.
5-DEFATTING & DRYING OF THE SKIN, WHICH MAY RESULT IN IRRITATION &
DERMATITIS.
Medical Cond Aggravated by Exposure:N/K
First Aid
First Aid:EYE:FL W/PLENTY OF CLEAN LUKEWARM LOW PRESS H*2O FOR 15
MIN,OCCASION LFT LIDS OPEN.GET MED ATTN.INHAL:RMV VICTIM TO FRESH
AIR & PROV O*2 IF BRTHING DIFF.GIVE ARTF RESP IF NOT BRTHING.GET
MED ATTN.KEEP VICTIM QUIET.NEVER GIVE UNCON PER LIQ.INGEST:DO NOT
INDUCE VOMIT.IF VOMIT OCCURS,KEEP HEAD BLW HIPS TO PVNT ASPIRATION
OF LIQ TO LUNGS.GET MED ATTN.NEVER GIVE UNCON PER LIQ.IF VICTIM HAS
(SUPP DATA)
Fire Fighting
Flash Point Method:SCC
Flash Point:22 F (-6 C)
Lower Limits:2.
Upper Limits:N/K
Extinguishing Media:FOAM, CO*2, OR DRY CHEMICAL
Fire Fighting Procedures:USE NIOSH/MSHA APVD SCBA & FULL PROT EQPT .
WATER MAY BE USED TO KEEP EXPOSED CONTAINERS COOL, & KEEP FLAMMABLE
STRUCTURES WET.
Unusual Fire/Explosion Hazard:WATER PRESSURE MAY SPREAD A FLAMMABLE
LIQUID FIRE. SEALED CONTAINERS MAY EXPLODE IF OVERHEATED.
Accidental Release
Spill Release Procedures:WARNING-FLAMMABLE. ELIMINATE ALL IGNITION
SOURCES. HANDLING EQUIPMENT MUST BE GROUNDED TO PREVENT SPARKING.
SOAK UP WITH AND ABSORBENT & PLACE IN NON-LEAKING CONTAINERS. SEAL
TIGHTLY FOR PROPER DISPOS AL.
Neutralizing Agent:N/K
Handling
Handling and Storage Precautions:TREAT AS A HAZARDOUS-FLAMMABLE
MATERIAL. KNOW APPLICABLE DOT REGULATIONS BEFORE ATTEMPTING TO
TRANSPORT THIS MATERIAL.
Other Precautions:N/K
Exposure Controls
Respiratory Protection:IN MORE CONFINED AREAS A NIOSH/MSHA APPROVED
RESPIRATOR EQUIPPED WITH ORGANIC VAPOR CARTRIDGE SHOULD BE WORN.
Ventilation:IMPORTANT-MUST PROVIDE ADEQUATE VENTILATION TO MAINTAIN
VAPOR CONCENTRATIONS BELOW ESTB TLV LIMIT AS GIVEN BY OSHA.
Protective Gloves:USE RUBBER GLOVES
Eye Protection:CHEM WORK GOGGLES,FACESHLD OPTIONAL FP N
Other Protective Equipment:HAVE EYE BATH AVAILABLE
Work Hygienic Practices:WARNING:CARE MUST BE TAKEN NOT TO EXCEED EXPOS
LIM FOR LOWEST TLV.WHEN IN DOUBT,WEAR APVD RSPTR & ORDER AIR SAMPLE
TESTS
Supplemental Safety and Health
BP:(79-82C).PH,ROUTES OF ENTRY & CARC:FIRST AID:INGEST LGE QTY, & IS
COMPL CONSCIOUS/ALERT,THEN ADMIN LUKEWARM H*2O(PINT).SKIN:FL W/H*2O
WHILE RMV CONTAM CLTHG & SHOES.FOLLOW BY WASHING W/SOAP & H *2O.DO
NOT REUSE CLTHG/SHOES UNTIL CLEANED. IF IRRITATION PERSISTS,GET MED
ATTN.KEY1:F3.
Chemical Properties
HCC:F3
Boiling Pt:B.P. Text:174-180 F
Melt/Freeze Pt:M.P/F.P Text:N/K
Decomp Temp:Decomp Text:N/K
Vapor Pres:N/K
Vapor Density:HTA
Spec Gravity:N/K
Evaporation Rate & Reference:2.3 (N-BUTYL ACETATE=1)
Solubility in Water:N/K
Appearance and Odor:CLEAR LIQUID
Percent Volatiles by Volume:80.0
Corrosion Rate:
Stability
Stability Indicator/Materials to Avoid:YES
MAY BE INCOMPATIBLE WITH OXIDIZING AGENTS & STRONG ALKALIES.
Stability Condition to Avoid:AVOID HEAT, SPARKS, OPEN FLAMES, &
INCOMPATIBLE MATERIALS LISTED BELOW.
Hazardous Decomposition Products:INCOMPLETE COMBUSTION FOR PRODUCTS
LIKE THIS MAY GENERATE HIGHLY POISONOUS CARBON MONOXIDE & OTHER
TOXIC GASES.
Conditions to Avoid Polymerization:AVOID HEAT, SPARKS, OPEN FLAMES, &
INCOMPATIBLE MATERIALS.
Disposal
Waste Disposal Methods:DISPOSAL MUST BE IN ACCORDANCE WITH CURRENT
LOCAL, STATE & FEDERAL REGULATIONS. CONTACT AN APPROVED DISPOSAL
FACILITY.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.